STABILIS ELECTRA

The avant-garde of stabilization

HOW DOES STABILIS ELECTRA WORK?

SR – Short Range System
The SR Short Range System is based on the experience with the Stabilis Electra System, with the intent to transfer our technology on boats under 20 metres.

Resulting from a profound innovation, the system joins the state-of-the-art electric engine Brushless Torque (available in three sizes) to a gear box.

Characterized by a unique design, the new system ensures the maximum compactness, reduced weights, a low energy consumption and a simplified installation. This system can also be powered at 24V DC.

HS – High Speed System
The new HS System is born from an evolution of the SE Stabilis Electra System, optimised for planing boats that can reach over 24 knots.

The system proposes several novelties compared to the previous range, among which: an optimized profile of the blades, which guarantees better performance further reducing the resistance, the use of new electronics for reduced encumbrance and higher performance, which allows to control different surfaces (helm or intruder) together with the stabilizing fins.

LR – Long Range System
The new LR System is designed to be installed on board displacement or semi-displacement boats.

This new product present remarkable benefits: more compact actuators with the same power of the equivalent SE system, higher performances, a new blades’ geometry designed for displacement boats, the possibility to install blades up to 5 sqm and new electronics with the possibility to integrate – and control – 8 control surfaces (two pairs of blades, helms, etc.). CMC Marine also considered the addition of inertial detectors that allow to analyse the movements of Roll, Pitch and Yaw, in order to permit the control of the platforms.

STABILIS ELECTRA SR BROCHURE

STABILIS ELECTRA HS BROCHURE

STABILIS ELECTRA LR BROCHURE

SR

TECHNICAL SPECIFICATIONS
(for one actuator)

Electrical motor: Permanent magnet synchronous motor.
Applicable range of electrical motor: 2.5 kW.
Standard fin size: 0,4 m2, 0,55 m, 0,7 m2
Fin rotational speed: From 0 deg/s to 80 deg/s
Voltage: 220V AC 1-phase or 3-phase or 24V DC.
Frequency: 50 Hz or 60Hz.
Maximum absorption range in underway condition*: 0,5 kW
Maximum power absorption in at anchor condition*: 1,6 kW
Fin type: Low drag profile series.
Shaft material: Duplex stainless steel.
Upper and lower bearing: Heavy-duty tapered roller bearings.
Lower seal: Two double-lip seals for maximum seawater protection. Easily accessible in a 316 stainless steel retainer.
Upper seal: Double-lip, spring-loaded seal for grease retention. The double-lip design also provides protection of the fin actuator against external contaminants.
Lubrication: Pre-packed with water-resistant grease for lifetime maintenance-free service. Reduction gearbox lubricated with mineral oil.
Fit & finish throughout: Painted RAL 9016 and polished.
Actuator weight (including the electric motor): 175 Kg
HS35

TECHNICAL SPECIFICATIONS
(for one actuator)

Electrical motor: Brushless type with elettromagnetic brake.
Applicable range of electrical motor: 3.5 kW motor rating.
Standard fin size: 0,60 m2
Fin rotational speed: From 0 deg/s to 80 deg/s
Voltage: 400V AC 3-phase or 200V AC 3-phase or 200V AC 1-phase.
Frequency: 50 Hz or 60Hz.
Maximum absorption range in underway condition*: 0,4 kW (with the 2,0 kW motor) – 0,7 kW (with the 3,5 kW motor)
Maximum power absorption in at anchor condition*: 1,2 kW (with the 2,0 kW motor) – 2,0 kW (with the 3,5 kW motor)
Fin attachment: Precision machined oversized self-locking taper.
Main shaft: 75 mm diameter duplex stainless steel.
Fin actuator housing material: High strength ductile iron.
Upper and lower bearing: Heavy-duty tapered roller bearings.
Lower seal: Two double-lip seals for maximum seawater protection. Easily accessible in a 316 stainless steel retainer.
Upper seal: Double-lip, spring-loaded seal for grease retention. The double-lip design also provides protection of the fin actuator against external contaminants.
Lubrication: Pre-packed with water-resistant grease for lifetime maintenance-free service. Reduction gearbox lubricated with mineral oil.
Fit & finish throughout: Painted RAL 9016 and polished.
Actuator weight (including the electric motor): 98 Kg
HS40

TECHNICAL SPECIFICATIONS
(for one actuator)

Electrical motor: Brushless type with elettromagnetic brake.
Applicable range of electrical motor: 2.0 kW or 3.5 kW motor rating.
Standard fin size: 0,60 m2, 0,80 m2
Fin rotational speed: From 0 deg/s to 80 deg/s
Voltage: 400V AC 3-phase or 200V AC 3-phase or 200V AC 1-phase.
Frequency: 50 Hz or 60Hz.
Maximum absorption range in underway condition*: 0,4 kW (with the 2,0 kW motor) – 0,7 kW (with the 3,5 kW motor)
Maximum power absorption in at anchor condition*: 1,2 kW (with the 2,0 kW motor) – 2,0 kW (with the 3,5 kW motor)
Fin attachment: Precision machined oversized self-locking taper.
Main shaft: 75 mm diameter duplex stainless steel.
Fin actuator housing material: High strength ductile iron.
Upper and lower bearing: Heavy-duty tapered roller bearings.
Lower seal: Two double-lip seals for maximum seawater protection. Easily accessible in a 316 stainless steel retainer.
Upper seal: Double-lip, spring-loaded seal for grease retention. The double-lip design also provides protection of the fin actuator against external contaminants.
Lubrication: Pre-packed with water-resistant grease for lifetime maintenance-free service. Reduction gearbox lubricated with mineral oil.
Fit & finish throughout: Painted RAL 9016 and polished.
Actuator weight (including the electric motor): 102 Kg
HS60

TECHNICAL SPECIFICATIONS
(for one actuator)

Electrical motor: Brushless type with elettromagnetic brake.
Applicable range of electrical motor: 5.0 kW motor rating.
Standard fin size: 1,00 m2, 1,40 m2
Fin rotational speed: From 0 deg/s to 80 deg/s
Voltage: 400VAC 3-phase or 200VAC 3-phase or 200VAC 1-phase.
Frequency: 50 Hz or 60Hz.
Maximum absorption range in underway condition*:  0.9 KW with the 5,0 kW motor
Maximum power absorption in at anchor condition*: 3.4 KW (with the 5,0 kW motor)
Fin attachment: Precision machined oversized self-locking taper.
Main shaft: 85 mm diameter duplex stainless steel.
Fin actuator housing material: High strength ductile iron.
Upper and lower bearing: Heavy-duty tapered roller bearings.
Lower seal: Two double-lip seals for maximum seawater protection. Easily accessible in a 316 stainless steel retainer.
Upper seal: Double-lip, spring-loaded seal for grease retention. The double-lip design also provides protection of the fin actuator against external contaminants.
Lubrication: Pre-packed with water-resistant grease for lifetime maintenance-free service. Reduction gearbox lubricated with mineral oil.
Fit & finish throughout: Painted RAL 9016 and polished.
Actuator weight (including the electric motor): 145 Kg
HS80

TECHNICAL SPECIFICATIONS
(for one actuator)

Electrical motor: Brushless type with elettromagnetic brake.
Applicable range of electrical motor: 5.0 kW or 7 kW motor rating.
Standard fin size: 1,60 m2, 1,85 m2
Fin rotational speed: From 0 deg/s to 80 deg/s
Voltage: 400VAC 3-phase or 200VAC 3-phase.
Frequency: 50 Hz or 60Hz.
Maximum absorption range in underway condition*: 1,2 kW (with the 5,0 kW motor) – 1,8 KW (with the 7,0 kW motor)
Maximum power absorption in at anchor condition*: 3,8 kW (with the 5,0 kW motor) – 7,0 KW (with the 7,0 kW motor)
Fin attachment: Precision machined oversized self-locking taper.
Main shaft: 100 mm diameter duplex stainless steel.
Fin actuator housing material: High strength ductile iron.
Upper and lower bearing: Heavy-duty tapered roller bearings.
Lower seal: Two double-lip seals for maximum seawater protection. Easily accessible in a 316 stainless steel retainer.
Upper seal: Double-lip, spring-loaded seal for grease retention. The double-lip design also provides protection of the fin actuator against external contaminants.
Lubrication: Pre-packed with water-resistant grease for lifetime maintenance-free service. Reduction gearbox lubricated with mineral oil.
Fit & finish throughout: Painted RAL 9016 and polished.
Actuator weight (including the electric motor): 235 Kg
HS120

TECHNICAL SPECIFICATIONS
(for one actuator)

Electrical motor: Brushless type with elettromagnetic brake.
Applicable range of electrical motor: 7.0 kW or 11.0 kW motor rating.
Standard fin size: 1,85 m2, 2,50 m2
Fin rotational speed: From 0 deg/s to 80 deg/s
Voltage: 400VAC 3-phase or 200VAC 3-phase.
Frequency: 50 Hz or 60Hz.
Maximum absorption range in underway condition*: 0,4 kW (with the 2,0 kW motor) – 0,7 kW (with the 3,5 kW motor)
Maximum power absorption in at anchor condition*:
Fin attachment: Precision machined oversized self-locking taper.
Main shaft: 120 mm diameter duplex stainless steel.
Fin actuator housing material: High strength ductile iron.
Upper and lower bearing: Heavy-duty tapered roller bearings.
Lower seal: Two double-lip seals for maximum seawater protection. Easily accessible in a 316 stainless steel retainer.
Upper seal: Double-lip, spring-loaded seal for grease retention. The double-lip design also provides protection of the fin actuator against external contaminants.
Lubrication: Pre-packed with water-resistant grease for lifetime maintenance-free service. Reduction gearbox lubricated with mineral oil.
Fit & finish throughout: Painted RAL 9016 and polished.
Actuator weight (including the electric motor):
HS160

TECHNICAL SPECIFICATIONS
(for one actuator)

Electrical motor: Brushless type with elettromagnetic brake.
Applicable range of electrical motor: 15 kW motor rating.
Standard fin size: 2,80 m2, 3,50 m2
Fin rotational speed: From 0 deg/s to 80 deg/s
Voltage: 400VAC 3-phase or 200VAC 3-phase..
Frequency: 50 Hz or 60Hz.
Maximum absorption range in underway condition*:
Maximum power absorption in at anchor condition*:
Fin attachment: Precision machined oversized self-locking taper.
Main shaft: 140 mm diameter duplex stainless steel.
Fin actuator housing material: High strength ductile iron.
Upper and lower bearing: Heavy-duty tapered roller bearings.
Lower seal: Two double-lip seals for maximum seawater protection. Easily accessible in a 316 stainless steel retainer.
Upper seal: Double-lip, spring-loaded seal for grease retention. The double-lip design also provides protection of the fin actuator against external contaminants.
Lubrication: Pre-packed with water-resistant grease for lifetime maintenance-free service. Reduction gearbox lubricated with mineral oil.
Fit & finish throughout: Painted RAL 9016 and polished.
Actuator weight (including the electric motor): 350 Kg
HS200

TECHNICAL SPECIFICATIONS
(for one actuator)

Electrical motor: Brushless type with elettromagnetic brake.
Applicable range of electrical motor: 22 kW motor rating.
Standard fin size: 4,00 m2
Fin rotational speed: From 0 deg/s to 80 deg/s
Voltage: 400VAC 3-phase or 200VAC 3-phase.
Frequency: 50 Hz or 60Hz.
Maximum absorption range in underway condition*:
Maximum power absorption in at anchor condition*:
Fin attachment: Precision machined oversized self-locking taper.
Main shaft:
Fin actuator housing material: High strength ductile iron.
Upper and lower bearing: Heavy-duty tapered roller bearings.
Lower seal: Two double-lip seals for maximum seawater protection. Easily accessible in a 316 stainless steel retainer.
Upper seal: Double-lip, spring-loaded seal for grease retention. The double-lip design also provides protection of the fin actuator against external contaminants.
Lubrication: Pre-packed with water-resistant grease for lifetime maintenance-free service. Reduction gearbox lubricated with mineral oil.
Fit & finish throughout: Painted RAL 9016 and polished.
Actuator weight (including the electric motor):
LR70

Coming soon!

LR90

Coming soon!

LR150

Coming soon!

LR170

Coming soon!

LR200

Coming soon!

ARE YOU INTERESTED IN
THE BEST COMFORT ON BOARD?

Start typing and press Enter to search